Outdoor Directional Dual-band Antenna ODI2-065R17M-GQ XX Pol, 65°Horizontal Beamwidth 694-960/694-960MHz 16.6/16.6dBi, E-Tilt: 0-10/0-10 Integrated RCU Electrical Specifications Frequency Range (MHz) R1 694-960, R2 694-960 694-824 790-894 Polarization Gain (dBi) Horizontal Beamwidth (°) Vertical Beamwidth (°) 15.5 16.3 70 65 61 9.1 8.3 0-10 / 0-10 1st Upper Sidelobe Suppression (dB) ≥17(0°), ≥16(5°), ≥15(10°) ≥25(typ.) Front-To-Back Ratio, 180°30° (dB) Cross-polar Discrimination@0°(dB) ≥17 VSWR ≤1.5:1 Isolation Intra-system (dB) ≥27 Isolation Inter-system (dB) ≥27 IM3 (2x43 dBm Carrier) (dBc) ≤-153 Maximum Power per Port (W) 500 Impedance (Ω) 50 Lightning Protection Direct Ground Mechanical Specifications Shipping Dimensions HxWxD(mm) / (in) Outline Drawing 2500x445x130 / 98.4x17.5x5.1 2815x570x285 / 110.8x22.4x11.2 Net Weight, Antenna (kg) / (Ib) 31.8 / 70.1 Net Weight, Mounting Kit (kg) / (Ib) 9.4 / 20.7 Shipping Weight (kg) / (Ib) Connector Type 52.0 / 114.7 4 x 4.3-10 Female Connector Location Radome Material and Color Bottom Fiberglass, Light Grey Operational Temperature (°C) -40 to +60 Operational Humidity (%) Operational / Max Wind Speed (km/h) Wind Load* @150km/h Frontal / Lateral / Rearside (N) 16.6 10.2 Electrical Downtilt (°) Dimensions, HxWxD (mm) / (in) 880-960 ±45° ≤95 150 / 200 1692 / 194 / 1970 *Wind Load refer to TIA-222-G standard RET Specifications Protocol to CCU/TMA Input Voltage Range (V) Power Consumption (W) Connectors to CCU Connectors to RCU Dimensions, HxWxD (mm) / (in) (excluding connector) Weight, w/o Mounting Kit (kg) / (lb) ©Comba Telecom. All rights reserved Information contained in this document is subject to confirmation at time of ordering. Specifications may differ depending on region and customers’ requirements. DS-Control:3-0-0 / 1217 3GPP / AISG 2.0 +10 to +30 DC ≤2(stand by); ≤13(operating) 8 pin connector, Male, conform to AISG 2.0 8 pin connector, Female, conform to AISG 2.0 100×53×26 / 3.9x2.1x1.0 0.16 / 0.35 1/2 Outdoor Directional Dual-band Antenna ODI2-065R17M-GQ XX Pol, 65°Horizontal Beamwidth 694-960/694-960MHz 16.6/16.6dBi, E-Tilt: 0-10/0-10 Integrated RCU Electrical Specifications BASTA Standard** R1 694-960, R2 694-960 Frequency Range (MHz) 694-824 790-894 880-960 15.3±0.6 16.1±0.5 16.4±0.5 Min Tilt 15.5 16.3 16.6 Mid Tilt 15.3 16.1 16.4 Max Tilt 15.0 15.9 16.2 70±4 65±3 61±2 10.2±1.4 9.1±1.0 8.3±0.8 Electrical Downtilt Deviation(°) ≤1.0 ≤1.0 ≤1.0 1st Upper Sidelobe Suppression (dB) ≥17 ≥18 ≥18 Upper Sidelobe Suppression, Peak to 20° (dB) ≥16 ≥18 ≥16 Front-To-Back Ratio, 180°30° (dB) ≥24 ≥25 ≥26 Cross-polar Discrimination@0°(dB) ≥19 ≥22 ≥22 Cross-polar Discrimination over Sector(dB) ≥9 ≥9 ≥9 Over All Tilts Gain (dBi) Horizontal Beamwidth (°) Vertical Beamwidth (°) **Values based on NGMN recommendations on Base Station Antenna Standards (BASTA). Connector Position Configuration Types 445 130 Connector Labeling*** Connect Code Frequency range Array R1 R2 694-960 694-960 l r ***R-Red, Y-Yellow, B-Blue, l-left array, r-right array, c-center array, t-top array, b-bottom array Accessories Model 00-ZJ10(08)(three mounting points) iRCU-302 Description Quantity 1 1 Mounting Kit, 0-8°tilt. Integrated RET Controller Quantity 1 Portable Control Unit Optional Products (order separately) Model PCU-H002 ©Comba Telecom. All rights reserved Information contained in this document is subject to confirmation at time of ordering. Specifications may differ depending on region and customers’ requirements. DS-Control:3-0-0 / 1217 Description 2/2